As usual whenever the mainboard and power board were exposed, I would look for any bulged capacitor, darkened area, a loosen connector and etc. Just like flyback transformer, the best testing equipment to test Fet and other components is actually the equipment itself because it runs on full operating voltage, frequency, signal and etc. How To Test Electronics Components. Guess what, you would not believe what have I just discovered-a defective 2N fet! A defective component in either primary or secondary side could cause low output voltage. I could not believe it was this faulty fet that causes all the output voltages to drop! However this monitor boards looks perfectly okay.
|Date Added:||23 December 2017|
|File Size:||26.94 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Hope you enjoy this article and more good articles to come everyday! Since I had checked all the components and could not locate the fault, the only way that I could do is to direct replace the semiconductor devices such as the diodes, scr, fet, and transistors. What you have just learned from here was that if all the suspected components tested good, the only way to reveal the truth is to direct replace the parts.
One by one of the semiconductor components I replaced and power on each time I had changed it to see if the bulb light up e151fob not. If the LCD monitor designed to run on 18 or 24 volts then you could use a light bulb from the big trailer. Guess what, you would not believe what have I just discovered-a defective 2N fet!
Wishing you all the best and happy repairing! Now we could use a 12 volt automobile brake light bulb to e11fpb at which section that is causing the low voltage output problem. When I measure the 12 volts line with a digital e151cpb, the readout was about 7- 8 volts which was very unusual.
From experienced I do encountered semiconductor components breakdown when under full operating voltage. Removing the fuse as shown in the photo and connect the bulb between the supply line and the cold ground could tell which section is giving problem.
Just like flyback transformer, the best testing equipment to test Fet and other components is actually the equipment itself because it runs on full operating voltage, frequency, signal and etc. I could not believe it was this faulty fet that causes all the output voltages to drop! I began to check again the defective 2N fet with my analog meter and peak electronic atlas component analyzer and the result is still the same-tested good!
A defective component in either primary or secondary side could cause low output voltage.
In fact this is good news to us because we know what the next step that we should make. It was quite challenging to troubleshoot this kind of problem where you are hundred percent sure that the primary side is giving problem yet you could not find out the culprit.
Removing the cover was a bit easy compared to other models.
As usual whenever the mainboard and power board were exposed, I would look for any bulged e151cpb, darkened area, a loosen connector and etc. After checking all the components I was surprised that all of them tested okay.
Dell E151FPb Computer Monitor User Manual
This e51fpb the time to really test your basic electronics e151fph because you now know at which area e15f1pb fault is and you just have to use your skills to locate the exact bad component. Dell Efpb LCD monitor came in with the complaint of no power but upon carefully look at the LCD you could see a very light blur white flashes across the screen and the power LED is not lit.
You could use this method but first you must confirm that the secondary filter capacitors, TL adjustable precision shunt regulator ic, optoisolators and components surrounding the optoisolator is working before you proceed to use the light bulb. The moments I have replaced this fet and power on, the bulb immediately light up. When the power is on the light bulb still do not lit and the sound still could be heard.
Dell EFPb – LCD monitor – 15″ Overview – CNET
There were not much components in the primary side, and you could easily check all of them in less than 20 minutes. Plasma TV Repair Ebook. How To Test Electronics Components.
However this monitor boards looks perfectly okay.